What “DJI Avata WiFi not showing” usually means
If your DJI Avata WiFi not showing issue appears after a restart, update, or flight session, it usually points to a pairing, visibility, or hardware state problem rather than a full system failure.
The DJI Avata and its companion apps rely on specific connectivity behaviors, so a missing Wi-Fi signal can come from settings, firmware, or a device that is not broadcasting as expected.
This guide explains the most common causes and the fastest ways to restore visibility so you can narrow down whether the issue is with the drone, the controller, the mobile device, or the surrounding environment.
Common reasons the Wi-Fi network does not appear
Several factors can prevent the DJI Avata from appearing in a Wi-Fi scan.
In many cases, the drone is functioning normally but is not in a broadcast state or is being blocked by a simple configuration issue.
- Power state mismatch: The aircraft, Goggles, or controller may not be fully powered on.
- Linking not completed: The drone may still need to be linked to the remote controller or goggles.
- Firmware inconsistency: Outdated or mismatched firmware can affect connectivity behavior.
- Auto-connect confusion: Some DJI devices use a connection flow that is not the same as a standard home Wi-Fi hotspot.
- Wireless interference: Dense RF environments can hide or disrupt the signal.
- Mobile settings: The phone’s Wi-Fi scanning, location permissions, or network settings may be limiting discovery.
Confirm the DJI Avata is in the correct state
Before changing settings, verify that the aircraft is actually powered on and ready to communicate.
The DJI Avata WiFi not showing problem often happens when users expect the drone to behave like a consumer hotspot, but DJI systems may require the goggles or remote controller to be active first.
Check the following:
- The battery is installed correctly and charged.
- The aircraft powers on with normal startup indicators.
- The goggles are on and linked, if your setup uses them.
- The remote controller is on and not in an error state.
- The mobile app is open and allowed to detect nearby devices.
If the aircraft never completes startup, reseat the battery and inspect for physical damage or debris in the battery contacts.
A weak power connection can prevent the Wi-Fi module from broadcasting.
Restart the drone and all connected devices
A clean restart clears temporary communication faults and is the quickest fix for many visibility problems.
Power off the aircraft, goggles, controller, and phone, then turn them back on in the correct order.
- Power off the DJI Avata.
- Power off goggles and remote controller.
- Close the DJI app on your phone.
- Restart the phone.
- Turn on the goggles or controller first, if your setup requires them.
- Then power on the aircraft and reopen the app.
This order matters because DJI ecosystems often establish a link chain before the device is discoverable in the expected way.
If the Wi-Fi still does not show, move to firmware and settings checks.
Check firmware on the aircraft, goggles, and controller
Firmware mismatch is a common cause of the DJI Avata WiFi not showing issue.
DJI updates often change connection behavior, and one device running older firmware may not communicate properly with another.
Use the DJI Fly app, DJI Assistant 2, or the device update prompts to confirm:
- The DJI Avata is on the latest stable firmware.
- The goggles match the aircraft firmware version requirements.
- The remote controller is updated to a compatible release.
- The mobile app itself is current.
If an update was interrupted, perform the update again with stable battery charge and a reliable internet connection.
Avoid mixing beta firmware with production hardware unless you intentionally use it for testing.
Verify phone and app permissions
On iPhone and Android, device discovery can depend on permissions that are easy to overlook.
If the app cannot scan properly, the Wi-Fi network may seem absent even when the drone is broadcasting.
Check these mobile settings:
- Location access: Some Android versions require location services for Wi-Fi scanning.
- Nearby devices permission: Grant the DJI app permission to detect accessories.
- Wi-Fi enabled: Make sure Wi-Fi is turned on, even if you plan to use cellular data.
- VPN disabled temporarily: VPNs can interfere with network detection and pairing flows.
- Battery optimization: Prevent the DJI app from being aggressively restricted in the background.
Also check whether the phone is auto-joining a known network and skipping scans.
Forgetting nearby networks temporarily can help isolate the issue.
Reduce interference and improve signal visibility
The 2.4 GHz and 5.8 GHz bands used by many drone systems can become crowded in apartments, event spaces, offices, and urban areas.
If the DJI Avata WiFi not showing issue only appears in certain locations, interference may be the main cause.
Try these adjustments:
- Move away from routers, smart home hubs, and Bluetooth-heavy areas.
- Test in an open outdoor space away from buildings.
- Turn off nearby hotspots and unused wireless accessories.
- Keep the drone and controller within a short initial range.
- Change orientation, since your body or metal objects can block signal paths.
Interference does not always make the signal disappear completely; sometimes it delays discovery long enough to look like a missing Wi-Fi network.
Inspect DJI Fly, goggles, and linking behavior
For the DJI Avata, the Wi-Fi issue may actually be a linking issue.
Depending on your setup, the aircraft may not present itself as a simple standalone network until the goggles and controller are properly linked and active.
Review the connection path:
- Confirm the goggles are paired to the aircraft.
- Confirm the remote controller is linked to the goggles or aircraft, depending on your configuration.
- Look for any on-screen status messages in DJI Fly or the goggles interface.
- Retry the link process if the devices show inconsistent status.
If you recently changed controllers, replaced goggles, or reset one of the devices, relinking may be required.
That step is often overlooked when users expect an existing Wi-Fi name to reappear automatically.
Reset network settings and app cache
When standard restarts do not help, resetting network-related settings can remove corrupted connection data.
This is especially useful if your phone has stored old credentials or if the app cached a failed pairing attempt.
- Forget old Wi-Fi networks on your phone.
- Reset network settings if the phone continues to misread nearby devices.
- Clear the DJI app cache on Android, if applicable.
- Reinstall the app only after backing up any required account data.
On iPhone, a network settings reset can also resolve scanning issues, though it will remove saved Wi-Fi passwords.
Use this step if permission and firmware checks do not change the result.
When the problem may be hardware-related
If the DJI Avata WiFi not showing issue persists after updates, restarts, and relinking, the aircraft or controller may have a hardware fault.
Damage from crashes, moisture exposure, or battery contact wear can affect the radio modules or startup behavior.
Signs of a possible hardware problem include:
- The aircraft powers on inconsistently.
- Firmware updates fail repeatedly on the same device.
- The same setup works with one phone but not another.
- No status lights or abnormal boot behavior appear.
- The drone becomes hot unusually fast or shows repeated disconnects.
At that point, test the Avata with known-good accessories if available, or contact DJI Support for a diagnostic review.
Include the exact device model, firmware versions, and the steps you already tried to speed up troubleshooting.
Fast checklist to troubleshoot DJI Avata WiFi not showing
Use this short sequence to isolate the issue efficiently:
- Power cycle the aircraft, goggles, controller, and phone.
- Confirm all batteries are charged and seated properly.
- Check firmware compatibility across all DJI devices.
- Enable location, nearby device, and Wi-Fi permissions on the phone.
- Disable VPNs and temporary network restrictions.
- Move to a low-interference area and scan again.
- Relink the aircraft and controller or goggles if needed.
- Reset network settings if discovery still fails.
Working through these checks in order usually reveals whether the issue is environmental, software-based, or tied to a specific component in the DJI Avata system.